The purpose of the SynCE project is to provide a means of communication with a Windows Mobile, or Windows CE, device from a computer running Linux, FreeBSD or a similar operating system.
MultiSync is a free modular program to synchronize calendars, addressbooks and other PIM data between programs on your computer and other computers, mobile devices, PDAs or cell phones. MultiSync works on any Gnome platform, such as Linux.
This is based on syncing my Dell Axim X3i with Evolution, but it should work with IPAQs and other Pocket PCs.
Connect your Pocket PC and type "dmesg" in a shell to see if the ipaq kernel module is loaded. The output might look like the following. Take note of the tty used for the connection.
usb 4-2: new full speed USB device using uhci_hcd and address 3
ipaq 4-2:1.0: PocketPC PDA converter detected
usb 4-2: PocketPC PDA converter now attached to ttyUSB02)
you can also use "cat /proc/bus/usb/devices" to check for a USB device that's using the ipaq kernel module.
T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.01 Cls=ff(vend.) Sub=ff Prot=ff MxPS=16 #Cfgs= 1
P: Vendor=413c ProdID=4002 Rev= 0.00
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=ipaq
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
SynCE Setup and Configuration
Install the required packages for SynCE
sudo apt-get install librra0 librra0-tools librapi2-tools libsynce0 synce-dccm synce-multisync-plugin synce-serial
synce-serial setup will be invoked by apt, follow this through using the default settings, unless you have reason to do otherwise.
local address: 192.168.131.102
remote address: 192.168.131.201
no dns entry needed
Perform the following command to tell SynCE where to look. This seems redundant.
sudo synce-serial-config ttyUSB0
Start the SynCE connection daemon by typing "dccm" in a shell. Use "dccm -p password" if your Pocket PC is password protected.
Initiate a serial connection by typing "sudo synce-serial-start" in a shell. You should be greeted with "synce-serial-start is now waiting for your device to connect".
"synce-pstatus" shows a LOT of information about your Pocket PC, such as current mode of operation, battery charge level, memory usage as well as backup battery status. If you want to see some other synce commands, type "dpkg -L librapi2-tools". You can use these commands to do things such as installing Pocket PC programs, etc.
Create the partnership between the Pocket PC and your computer. There are 2 slots on the device, so the INDEX can be 1 or 2.
synce-matchmaker create INDEX
You should see the following message
Partnership creation succeeded. Using partnership index INDEX.
Multisync Setup and Configuration
Install the required packages for Multisync
sudo apt-get install libmultisync-plugin-all multisync
Or, alternatively if you want to skimp on the packages
sudo apt-get install libmultisync-plugin-evolution libmultisync-plugin-backup multisync
Start Multisync by typing "multisync" in a shell. You can also do via Applications > Accessories > Multisync, but the shell gives you a lot of feedback which can be helpful the first time you use it.
Create a new synchronization pair where one of the plugins is "SynCE Plugin" and the other is "Ximian Evolution 2", the order doesn't matter. You may need to create a new Contact List, Task List and Calendar, so that the default ones aren't used. I'm not sure if this is needed, but it was mentioned in the other thread.
Press the "Sync" button.
Initially, You may not have entries in Evolution so for some reason, You need to modify all of the entries on Pocket PC so that the timestamp would register each entry as a ‘change', otherwise no entries were sync'd.
Disconnecting Your Pocket PC
"killall -HUP dccm" to kill the serial connection.
run "synce-serial-abort", if the above command doesn't work.
Incoming search terms:
- multisync ubuntu 12 10
- synce ubuntu
- synce ubuntu precise
- ubuntu pocket pc
- axim x51v evolution ubuntu
- pocket pc sync linux
- synchronize pocket pc ubuntu
- ubuntu connect ipaq pocket pc 3600